BLACKFAST 513 ACID PICKLE MEDIUM
 


USE:
Use as supplied or 50% solution in water.

APPLICATION: Rust and scale can be removed by immersion in 50% solution of Blackfast 513 in water for 10 minutes. Use of undiluted Blackfast 513 or immersion for a longer period may be necessary for scale on hardened steels. When heavy rust and scaling are present, it is important to maintain the strength of the pickle bath by periodic replenishment of Blackfast 513. Addition of a surfactant, Blackfast 500, may be necessary if some extra degreasing is required. Ensure rinsing is sufficient to remove all traces of Blackfast 513 before proceeding further.

Blackfast 513 should not be used for cast iron components because it penetrates the surface too deeply and is very difficult to rinse clean. Blackfast 505 should be used for cast iron.

TANK MATERIAL: Tanks should be of suitable polypropylene.

Blackfast 513 acid pickle medium is part of the Blackfast range of products for the chemical blacking of iron and steel at room temperature.

Blackfast Chemicals continues to improve the quality and performance of its range of products and reserves the right to modify product formulations without prior notice.

SAFETY DATA:

1. IDENTIFICATION OF THE SUBSTANCE PREPARATION AND OF THE COMPANY

PRODUCT NAME: BLACKFAST 513 ACID PICKLE APPLICATION: Pickling iron and steel COMPANY: Blackfast Chemicals
ADDRESS: 78 Coombe Road, New Malden, Surrey KT3 4QS, England
TEL/FAX NO’S: Tel: 0181-336 2900 Fax: 0181-336 0909

2. COMPOSITION/INFORMATION ON INGREDIENTS

COMPOSITION: Hydrochloric Acid with surfactants
HAZARDOUS INGREDIENTS: Hydrochloric Acid (>25%)
SYMBOL: C
RISK PHRASES: R34, R37
EEC NO: 231 -595-7

3. HAZARDS IDENTIFICATION

Corrosive

4. FIRST AID MEASURES

INHALATION: Remove to fresh air. Seek medical aid.
INGESTION: DO NOT INDUCE VOMITING. Gargle, rinse mouth and drink large amounts of water. Seek medical aid.
SKIN: Remove contaminated clothing. Wash well with soap and plenty of water. Seek medical aid.
EYES: Flush with clean water immediately for 15 minutes. Seek medical aid.

5. FIRE FIGHTING MEASURES

Non flammable. Will not support combustion.
Decomposition products: Hydrogen Chloride, Chlorine, Chlorine Oxides. Wear self-contained breathing apparatus and protective clothing to prevent contact with skin and eyes.

6. ACCIDENTAL RELEASE MEASURES

PERSONAL PRECAUTIONS: When dealing with a spill note the recommendations in Section 7
ENVIRONMENTAL: Prevent entry into drains, sewers and water courses
SPILLAGE: Absorb liquid in absorbent clay granules and mix with solid Sodium Bicarbonate to neutralize..

7. HANDLING AND STORAGE

Avoid inhaling the vapour. Avoid contact with skin and eyes. Store in clean, dry conditions between 5 and 400 C away from direct sunlight. Keep container closed and ensure label intact and legible.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Occupational Exposure Limits: Hydrogen Chloride 15 min ref. period 7 mgm-3 (EH40/94)
Cover when not in use. Local exhaust ventilation is recommended when in continuous use.
Personal protection: Wear impervious (PVC) gloves, eye protection and plastic apron. Remove contaminated clothing immediately.

9. PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE: Yellow liquid
SPECIFIC GRAVITY: 1.13 @ 200C
SOLUBILITY/MISCIBILITY IN WATER: Complete
FLASH POINT: N/A
pH: 1.0 - 1.5

10. STABILITY AND REACTIVITY

Solution is stable under normal conditions. Avoid temperatures above 500 C and direct sunlight. Corrosive gas is released on heating. Avoid sources of ignition. Incompatible chemicals - strong bases which react generating heat, and metals which produce a flammable gas, Hydrogen.

11. TOXICOLOGICAL INFORMATION

Causes burns and is destructive to tissue of the mucous membranes and upper respiratory tract, eyes and skin. Inhalation may cause spasm, inflammation and edema of the larynx and bronchii, chemical pneumonitis and pulmonary edema. Symptoms of exposure may include burning sensation, coughing, wheezing, laryngitis, shortness of breath, headache, nausea and vomiting.

12. ECOLOGICAL INFORMATION

Not assessed.

13. DISPOSAL INFORMATION

Disposal must be in accordance with local and national legislation. Dispose through an authorized waste contractor to a licensed site.

14. TRANSPORT INFORMATION

PACKING GROUP: II Corrosive substance
UN NUMBER:1789
CAS NO: 7647- 01 - 0

15. REGULATORY INFORMATION

HAZARDOUS INGREDIENTS: Hydrochloric Acid
SYMBOL: C
RISK PHRASES: Causes burns. Irritating to respiratory system.
SAFETY PHRASES:
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. In case of accident or if you feel unwell, seek medical advice immediately (show label where possible).
STATUTORY INSTRUMENTS:
Health and Safety at Work Act 1974. Chemicals (Hazard Information and Packaging) Regs 1993 (Si 1746). Control of Substances Hazardous to Health Regs 1988 (Si 1657). Environmental Protection Act 1990.
CODES OF PRACTICE:
Classification and labelling substances dangerous for supply (COP 22). Waste management: The duty of care.
GUIDANCE NOTES:
Occupational exposure limits (EH 40). Classification, Packaging and Labelling of Dangerous Substances Regs. 1984 HS(R)22.

16. OTHER INFORMATION

Read the Application Data Sheet before using this or any Blackfast product. The product is intended for the stated use only. Do not use the product for any other application without obtaining advice from us beforehand. If this product is for resale, ensure that the purchaser receives a copy of this information. If this product is for end use, ensure that your employees and others who may be affected are aware of the contents of this sheet.

This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any other process. Such information is to ths best of the company’s knowledge and belief, accurate and reliable as of the date indicated. However, no warranty, guarantees or representation is made as to its accuracy, reliability or complete ness. It is the user’s responsibility to satisfy himself as to the suitability of such information for his own particular use.

 
back to top
Tel 02 9834 6034 - Fax 02 9834 6105 - Email for info sales@asteg.com

Sales Office: 134 Pine Creek Circuit, St Clair NSW 2759 Sydney (Aust)
Warehouse: Unit 3008 / 2 Zeleny Rd Minchinbury NSW Sydney (Aust)

home | about us | news | specials | faq | contact us | search
Prices shown exclude GST and are subject to change without notice.
© Asteg Sales 2002.